{"product_id":"nissan-s14-s15-front-drift-angle-lock-kit-v3-for-front-rack-wisefab","title":"Nissan S14 S15 Front Drift Angle Lock Kit V3 for Front Rack Wisefab","description":"\u003cp\u003eWisefab “Odi Edition” V3 Nissan S-Chassis lock kit relocates the steering rack to the front of the subframe - allowing for better car control at medium to full-lock and preventing steering “bind” at max angle. Steering feel is more consistent throughout the entire sweep which allows for a more “usable” range of lock overall. Ackermann and bump-steer have also been revised for a more refined driving feel. The addition of a quick caster adjuster to the lower control arm also makes adjusting caster at the lower arm both quick and easy. The “Odi Edition” kit is truly the ultimate culmination of angle kit solution for the S-Chassis!\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eToe in\/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive then toe is 0\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eCamber: -4 +\/-0,5\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eCaster: 3,5 ´+\/-0,5\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMore usable lock.\u003cbr\u003e65+ degrees of lock, better feel and precise handling. You could tune your steering geometry from parallel to positive Ackermann in just a few minutes even at trackside without messing up an alignment. \u003cbr\u003eAckermann adjustment kit included.\u003c\/li\u003e\n\u003cli\u003eLess sensitive steering.\u003cbr\u003eIncreased steering ratio for smooth handling.\u003c\/li\u003e\n\u003cli\u003eMore suspension travel.\u003cbr\u003eLess interference risk at full droop. Longstroke coilover kits can be used.\u003c\/li\u003e\n\u003cli\u003eLighter and stronger.\u003cbr\u003eOptimized design in combination with high strenght steel is used.\u003c\/li\u003e\n\u003cli\u003eHigher roll center (RC).\u003cbr\u003eOn Wisefab knuckle, the ball joint is lowered 60mm, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles.\u003c\/li\u003e\n\u003cli\u003eFast and convenient caster adjustment from lower control arm.\u003c\/li\u003e\n\u003cli\u003eAdjustable camber from top-mount\u003c\/li\u003e\n\u003cli\u003eAdjustable lock stopper.\u003c\/li\u003e\n\u003cli\u003eOne piece lower control arm desing. \u003cbr\u003eLower links are replaced with one arm. Drifting with higher steering angle the stiffness and packaging would become an issue. Therefore lower one piece arm is used.\u003c\/li\u003e\n\u003cli\u003eVery good camber control and minimal bump steer with high steering angles. \u003cbr\u003eOn drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.\n\u003cul\u003e\n\u003cli\u003eSteering jacking control.\u003cbr\u003eDuring drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.\u003c\/li\u003e\n\u003cli\u003eConsistent and predictable self-alignment torque. \u003cbr\u003eCaster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eKit includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable coilover upper mounts, Formula Drift compliance.\u003c\/li\u003e\n\u003cli\u003eKnuckles with hardware.\u003c\/li\u003e\n\u003cli\u003eLower control arms.\u003c\/li\u003e\n\u003cli\u003eAssembeled tie rods.\u003c\/li\u003e\n\u003cli\u003eRack relocating kit.\u003c\/li\u003e\n\u003cli\u003eRack installation guide.\u003c\/li\u003e\n\u003cli\u003eInstallation guide.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eOther components, packaging and clearance.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis kit assumes coilovers to have enough clearance.\u003c\/li\u003e\n\u003cli\u003eDepending on the type of engine and oil sump setup, additional modifications to the subframe and\/or the oil sump may be necessary.\u003c\/li\u003e\n\u003cli\u003eDepending on rim width and ET, wider fenders or fender flares would be needed.\u003c\/li\u003e\n\u003cli\u003eWith tire diameter up to 635mm (215\/45R17, 225\/45R17, 235\/40R17, 225\/40R18 etc) and lowered ride height the inner wheel wells need to be slightly modified.\u003c\/li\u003e\n\u003cli\u003eRecommended backspacing is 135-140mm (7“ ET45; 8“ ET35; 9“ ET25).If ET is smaller, then wheels stay more outwards, if ET is bigger, then spacers need to be used.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"WISEFAB","offers":[{"title":"Default Title","offer_id":52788769882454,"sku":"WF1401","price":2300.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0935\/6119\/2790\/files\/wf1401-1_jpg.png?v=1773145473","url":"https:\/\/driftmafia.life\/products\/nissan-s14-s15-front-drift-angle-lock-kit-v3-for-front-rack-wisefab","provider":"DriftMafia","version":"1.0","type":"link"}